Adora Belle Dearheart Part 2

With ten days to go until the North American Discworld Convention, my Adora Belle Dearheart costume is finished!

If you missed the first part of this blog, which talks about design, patterning, and building the main body of the dress, you can read it here:

Adora Belle Dearheart Part 1

When I left off, the dress still needed a collar and sleeves. The collar is a simple standing collar, which was very popular in the 1890s. It is lined with the same red fabric as the rest of the dress, and interfaced with canvas to keep it stiff.

Stitching the lining, with attached interfacing, into the collar.

The sleeves are two-part with bent elbows. They are fitted through most of the arm, with a puff at the shoulder that gives them an almost spiky appearance.

They have false cuffs–meaning that an extra piece of fabric was superimposed onto the end of each sleeve piece before construction. This is merely decorative–the cuffs can’t fold down or anything, as they are permanently attached to the piece, and sewn into the sleeve seams.

I attached the false cuffs with a row of decorative herringbone stitching in grey buttonhole silk,

The under and upper sleeves with false cuffs attached.

The upper sleeve has a slight gather at the elbow when it attaches to the under sleeve–this helps give it a bit  of flexibility when moving.

The sleeve lining is cut to fit smoothly into the armscye, while the fashion fabric is cut to create the large poof. There is a piece of wadded up stiff netting inside the puff between fabric and lining to keep it, well, puffy.

I ended up having to tear out and re-pleat, reshape, and otherwise adjust the sleeves seven different times before I was satisfied with the look, but it turned out worth it!

With all the pieces attached, it was time for lots of finishing touches. That started with finishing off the raw edges of the crossover pieces. The neckline and armscye edges are simply turned under and overcast, but the shoulder seam edge has a piece of heavy cotton facing to give the buttonholes more stability.

The darts also each got a row of herringbone stitching, which both looks nice and holds down the extra fabric on the inside. I got this detail from one of the original dresses I referenced in Part 1.

At this point, I remembered that I wanted to add a pocket to this dress–never underestimate the importance of having a pocket in any costume you’re planning to wear at an all-day event!

The pocket sits flat inside the bulk at the back of the skirt, with an opening in the center back seam. It is just under the bum-pad, so that any bulk from items is completely hidden in the extra volume. It is made of three pieces–one back piece, and two front pieces, joined above and below a slit that matches up with the slit in the skirt.

Here is the pocket on the inside of the skirt. The ties keep the bulk of the skirt contained in a nice tail, so that it doesn’t just flop all over the place.

I also stitched a piece of re-enforcing twill tape up the center back skirt seam to help keep it from stretching, since it is both cut on the bias, and the only part of the dress that isn’t lined.

Adding a final row of herringbone stitch just below the collar.

I swear I also hemmed the dress, though I seem to have forgotten to photograph that part. There is a cotton hem facing out of the same material as the one on the shoulder.

The final task was also one of the most daunting: buttonholes and buttons. I don’t normally have an issue with buttonholes, but this particular dress required 47 of them. I did have a contingency plan whereby if I drove myself mad doing buttonholes before they were finished, I would close the lower half of the skirt with hooks and eyes, and simply sew buttons over the top, but I really liked the look of a row of silk-bound buttonholes marching down the skirt, so I pressed on. Adora Belle is a character whose clothes should be a pain to get off.

I used a pair of calipers to mark the buttonholes evenly down the side of the dress.

I was sewing buttonholes for days… I could get about six done on a week day after work, more on a weekend day.

There are four buttons on the shoulder, and 43 down the side.

I absolutely adore the vintage buttons I found on Etsy store The Vintage Pillbox! And there are still more available!

It was so satisfying to get the last few on!

I wrestled and fought with this costume a lot as I was building it, but I am so thrilled with how it turned out! The fit is great, the crazy closure worked out properly, and the way it moves makes me want to turn in little circles with joy! (You can see it moving in a video on my Instagram, which is also linked on the right.)

Disclaimer: I do not smoke, but you can find New Rule FX’s fantastically realistic cigarette prop (available in filter or non-filter varieties), here.

If you are interested in the wig I’m wearing, which is hand-tied human hair, and can be styled in almost any way you can imagine (I have so far used it for Snow White from Once Upon a Time, 1840s, and Adora Belle/1890s, and plan to use it in many more ways in the future), check out my day job at Custom Wig Company!

You can see pictures of this wig in action in other styles on my Facebook page or Instagram. You can also read more about the process of making one of these versatile beauties in my post To Make a Wig.

Slideshow of detail shots, including me being very excited about my pocket! Also my super awesome black and red clocked stockings from Amazon Drygoods.

This slideshow requires JavaScript.

Only ten days left, so I’ll be fully immersed in Brandon’s golden jacket until we leave. I am so excited!!! In ten days, I depart for a city I’ve always wanted to go to (New Orleans), to attend an event celebrating my absolute favorite book series (Discworld), and just as an extra bonus, it’s my first anniversary! What could be better?

Edit to add a few photos from outside our hotel in New Orleans! (Including Brandon in his Moist Von Lipwig suit!)