1870s Unmentionables: Layer 3-Bustle and Petticoat

And here we are! The third and final segment of 1870s undergarments! If you missed the last two, check out:

1870s Unmentionables: Layer 1-Chemise and Drawers

and

1870s Unmentionables: Layer 2: Corset

The final additions to the silhouette are all about skirt volume. Skirts in the early 1870s were just beginning to deflate from the full elliptical hoops of the 1860s. But instead of going completely away, the volume moved up, settled just below the back waist and became the bustle. So this:

Fashion Plate from The Englishwoman’s Domestic Magazine, May 1867

Became this:

Fashion Plate from Victoria, March 1870

I was going for a silhouette from the very beginning of the Bustle Era, so my base layer is Truly Victorian’s voluminous Grand Bustle, which gives support both to the bustle shape in the back, and also around the hem, so that the entire skirt maintains some volume. The pattern is very simple and easy to follow, and you can even buy pre-cut boning for your size right from Truly Victorian‘s website, which was both cheaper and easier than buying a 10 yard roll.

My fabric is a gorgeous purple cotton sateen from Renaissance Fabrics. I can’t say enough good things about this fabric, is beautifully soft, has a stunning sheen, and I love the color!

It begins with stitching the two front pieces together, leaving the top of the seam open, and stitching down the seam allowances to make a placket where the bustle will close.

Then you put the boning channels, which are pieces of bias tape, in the back. I used tracing paper and wheel to mark where the channels needed to go.

There are four horizontal channels, which are very straightforward:

And then one more, which is made of two diagonal pieces and one small “tab”, for a fifth bone to go through. This bone helps the bustle keep a nice dome shape without drooping.

 

Ruffles all down the back help give the shape extra floof, while also softening any awkward lines created by the boning. The final ruffle at the bottom won’t go on until everything else is put together.

My ruffles are made of cotton organdy because it’s lightweight and easy to gather, but stiff enough not have the volume completely crushed out of it by heavy skirts. I bought white organdy and dyed it purple to (sort-of) match the sateen. It’s not perfect, but close enough for under-garments, right?

The back also has a brace that pulls in the edges of the piece to make sure all the volume goes straight back, rather than expanding too much to the sides.

It was pretty nuts to crush base fabric, brace, ruffles, and bias tape into the side seams, but it did happen.

Once the fronts and backs are put together, one more bias tape boning channel goes around the entire bottom of the skirt, about four inches up from the hem. The hem itself is also used as a boning channel.

The final ruffle can either stay on the back with the rest of them, or go all the way around the hem. I chose the latter option because why say no to MORE FLOOF?!

The final task is to get everything gathered onto the waistband. I decided to gather the back volume, and pleat the front/side volume to give myself as much poof in the back as possible, while keeping the front relatively smooth.

I finished off the inside of the waistband with a quick whipstitch.

Put the boning in:

And voilà!

The petticoat is view one of Truly Victorian’s Victorian Petticoats pattern. It’s a great, straightforward pattern that includes variations to get you from the early 1870s all the way through the turn of the century.

The petticoat starts the same way as the bustle: sew a center seam, leaving the top open for a placket, though this time the closure is at center back.

The upper portion of the petticoat is very simple: there are darts in the front and side pieces to eliminate bulk, and then a nice large back section to gather up over the bustle. Things start getting exciting with the middle section, the flounce. It is gathered onto the top section, and ornamented with tucks, which help to stiffen it. The tucks take forever, since the piece is about five yards around. I also added an extra two tucks to shorten the petticoat.

And then there are 10 yards of ruffle to contend with. Once again I did this in organdy for extra stiffness. The ruffle gets hemmed first, then gathered onto the middle flounce. When gathering, I normally divide up the piece into quarters in order to distribute the gathers more evenly, but this ruffle was so huge, I had to divide it into eighths!

And one more waistband, this one narrower and closed with a drawstring:

And we’re done!

And that’s a wrap on the undergarments! Next comes the underskirt! I will probably be working on this project concurrently with my upcoming Adora Belle Dearheart cosplay, since the North American Discworld Convention will be here before I know it, and I have a petticoat, gown, possible jacket, and parts of Brandon’s suit to complete before September!

Idle hands, you know…